UEEEL0079 — Plan and analyse LV electrical apparatus

Generate a complete, audit-ready assessment tool for this unit in minutes: candidate assessment, assessor guide with model answers, and a coverage matrix mapped to every component below. Reviewed and approved by your qualified person, exported under your branding.

Generate UEEEL0079 free See a real sample

Every new account includes a free credit — no card, no subscription.

What an assessment for UEEEL0079 must cover

78 assessable components: 3 elements (10 performance criteria), 7 performance evidence and 61 knowledge evidence requirements. An audit-defensible tool maps every question and task back to these — that mapping is the coverage matrix Auditori generates alongside the assessment.

Elements & performance criteria

1 Prepare to plan and analyse single and three phase low voltage electrical apparatus

1.1Work, health and safety (WHS) / occupational health and safety (OHS) risk control measures are identified and applied
1.2Apparatus to be analysed, and scope of work to be undertaken are identified and confirmed
1.3Tools, equipment and testing devices needed to carry out the work are obtained and checked for correct operation and safety

2 Plan and analyse single and three phase low voltage electrical apparatus

2.1Apparatus is confirmed as being isolated where necessary in accordance with WHS/OHS requirements
2.2Apparatus is analysed using measured and calculated values as they apply to single and three-phase low voltage apparatus
2.3Apparatus problems are identified from analysis and solutions for rectification are recommended
2.4The use of apparatus in a specified electrical installation is planned in accordance with requirements

3 Complete and document work

3.1Results of analysis are recorded
3.2Justification for apparatus selection and installation planning is documented
3.3Work completion is documented and stored in an appropriate location

Performance evidence

analysing the operating parameters of existing apparatus
recommending alterations to existing apparatus to comply with specified operating parameters
determining the cause of problems in existing apparatus
recommending solutions for identified apparatus problems
determining conditions causing existing apparatus to be unsafe
justifying selection of apparatus for a specified range of applications and operating parameters
planning apparatus installation in accordance with requirements

Knowledge evidence

lighting including:
wiring diagrams for lighting circuits
switching methods for lighting circuits
cabling requirements for lighting circuits
correct operation of installed lighting circuits
required compliance testing
basic concepts, terminology, principles and standards relevant to lighting
types of luminaires and incandescent lamps
operation of different lamp types including their control equipment
expected lamp life, colour rendering and efficacy for different lamp types
lighting layout in terms of visual comfort and relevant Australian standards
types of low intensity discharge lamps
types of high intensity discharge lamps
LED lighting and its applications
Neon, Argon and Xenon lighting and their applications
power factor requirements
comparison of incandescent, low intensity discharge, high intensity discharge, LED and other types of lighting
emergency and evacuation lighting and lighting control including:
factors and requirements of emergency and evacuation lighting concerning illumination levels, luminaire positioning and operating period
characteristics of maintained, non-maintained and sustained emergency lighting systems
arrangement of batteries in point and central bank emergency lighting supply systems
lighting control methods
fire protection – residential fire and smoke alarms including:
types of fire and smoke alarms
regulations and standards requirements regarding residential fire and smoke alarms
locations for residential fire and smoke alarms
operation of typical residential fire and smoke alarms
electrical heating control devices including:
methods of manual heat control
methods of automatic heat control
types and application for common thermostats
operation of common thermostats
sensitivity and differential of thermostats
testing of a thermostat
applications and operation of simmerstats
electronic heat control (phase control and zero voltage switching)
fixed electrical heating appliances including:
determining the heat energy in joules and kWh in a simple heating process
methods of heat transfer
determining the heat energy input and output of a heating process
operation of reverse cycle air conditioning
electrical water heater operation including:
types of water heaters (instantaneous and storage) and their methods of control
intrinsic safety (pressure relief and thermal cut-out)
testing of over temperature cut-out point of a thermostat
switchboard requirements to supply a controlled load water heater
internal circuit of a twin element water heater, and supply connections
solar heating system and its integration into an installation
alternative supplies including:
reasons for the installation of alternative supplies
types of alternative supply systems
characteristics and operation of uninterruptible power supplies (UPSs)
batteries including:
common types of primary cells and secondary batteries and typical applications
terminal voltage of common primary cells and secondary cells
correct storage, handling and disposal techniques for cells and batteries
charge/discharge cycle for a secondary cell
effect of internal resistance on a secondary cell
state of charge of a secondary cell
commissioning procedures for various secondary batteries
safe working procedures when working with secondary cells and batteries.

Unit content sourced from training.gov.au — © Commonwealth of Australia, licensed under CC BY 4.0. Auditori is not affiliated with the Department of Employment and Workplace Relations.

See what you get before you start

Real, unedited Auditori output (RIIHAN201E shown), branded for a sample RTO:

Questions about assessing UEEEL0079

What does an assessment tool for UEEEL0079 need to cover?

To satisfy the Principles of Assessment and Rules of Evidence, an assessment for UEEEL0079 needs to address all 78 unit components: 3 elements with 10 performance criteria, 7 performance evidence requirements, 61 knowledge evidence requirements, and the foundation skills. A coverage matrix mapping each question and task to these components is what an auditor looks for.

How does Auditori generate an assessment tool for UEEEL0079?

Auditori pulls the current release of UEEEL0079 from training.gov.au and generates a complete package: candidate assessment, assessor guide with model answers and observation criteria, and a coverage matrix mapping every component. A suitably qualified person then reviews and approves the draft in a built-in workflow — consistent with ASQA's guidance on AI use in VET — before export as branded PDF and editable Word.

Is the first assessment tool really free?

Yes. Every new account includes one free credit — enough to generate the complete assessment tool for UEEEL0079 — with no card and no subscription required. After that it's pay-as-you-go per unit.

Can I check my existing UEEEL0079 assessment instead of generating a new one?

Yes — upload your existing assessment or learner guide and Auditori maps it against every element, performance criterion, PE and KE of UEEEL0079, showing exactly what's covered and what's missing. Mapping costs a quarter of a credit.

Related units

Your UEEEL0079 assessment tool, in minutes.

First unit free. No card, no RTO registration, no subscription.

Generate UEEEL0079 free